Appliance Error Code Guide Codes, causes & fix order
Washers · LG

LG Washer Error Code dE / dHE

A door that looks shut and still shows dE is the one appliance fault almost anyone can settle in five minutes — and one of the few where forcing the handle turns a cheap repair into an expensive one.

Checked against LG support documentation Updated 17 November 2026 7 min read

The short answer

  • dE — the door is not closed, or the machine cannot confirm it is closed and locked.
  • dHE — the lock is not reporting to the board. Same checks, more suspicion on the lock.
  • First: a sock or a drawstring in the seal, residue on the glass edge, a bent striker, or a door that needs a firm push.
  • If the door will not open: drain the water first. The lock is holding by design, not by fault.

What the machine is checking

A front loader will not fill or spin with the door open, because both involve water at pressure and a drum turning at speed. The control board therefore checks two things before a cycle starts: that the door switch is closed, and that the lock has engaged. dE is set when the first check fails or the two disagree; dHE is set when the lock itself does not respond.

On a top loader the same logic applies to the lid, and LG uses its own letters for that. The checks below are for the front-load door, which is where this code appears most.

The five-minute check

  1. Open the door and look at the seal all the way round. A sock, a sleeve or a drawstring caught in the fold is the most common cause of a code that appears only with certain loads.
  2. Wipe the door glass edge and the seal with a damp cloth. Detergent film stops the door seating the last few millimetres.
  3. Close the door firmly until you hear the latch. A gentle push is not always enough on a machine with a new seal.
  4. Look at the striker — the small hook on the door that enters the lock. It should be straight, tight and undamaged. A bent striker is common after a door has been pushed shut with a knee.
  5. Start a short cycle. If the code clears, the fault was mechanical and cost nothing.

When it is the lock

The door lock is a small unit behind the front panel with a solenoid, a switch and a connector. Failures come in three forms: the solenoid no longer moves, the internal switch no longer reports, or the connector and harness are damaged by heat and vibration.

With the machine unplugged, remove the front panel or the retaining ring to reach the lock. Check the connector for scorching and pushed-back pins, and check the harness where it passes the hinge. If the lock has continuity only when the door is pushed hard, the lock is worn.

Never force a locked door open. The handle and hinge break long before the lock gives way, and a drum full of water will follow. Drain through the filter housing first, then release the lock as the manual describes.

What it points to

FindingPartAction
Clothing or residue in the sealNoneClean; close firmly
Bent or loose strikerStrikerStraighten or replace
Torn or deformed sealDoor sealReplace — a leaking seal also causes LE codes
Lock clicks but code staysDoor lockReplace the lock unit
Scorched connectorHarness or lockReplace the damaged part, not just the plug
New lock, same codeControl board inputTest the board input before replacing it

Why it appears mid-cycle

A code in the middle of a wash usually means the door was nudged, the machine is on an uneven floor and the door has moved slightly in its frame, or the lock is dropping out when it warms up. Check that the machine stands level and that the door hinges are tight. A machine that rocks will produce intermittent door codes for months.

Repair or replace

A lock is a modest part and a striker is cheaper still. If a damaged lock has followed a broken hinge or a bent door, price the door as well before deciding — the cost formula helps here.

Frequently asked questions

The door is locked and the display shows dE — what do I do?

Wait two or three minutes for the lock to release. If it does not, drain the drum through the filter housing, then follow the manual's manual-release procedure. Forcing the handle is the last resort and usually breaks it.

Will the machine work with the door switch bypassed?

It may, and it is dangerous. A spinning drum with an open door is exactly the accident the switch exists to prevent. Do not bypass it.

My top loader shows dE too — same fix?

The logic is the same but the parts differ: lid switch and striker rather than a door lock. Check that the lid closes squarely and nothing is trapped under it.

Sources

  1. LG support — washing machine error code guidance covering the door error family, accessed 17 November 2026.
  2. Service documentation on the door lock circuit and its feedback switch.
  3. Editorial review against the parts trade: striker damage and lock failures on LG front loaders.

General information only. Lock type, panel access and code wording differ by model. Confirm against your machine's documentation and unplug before removing a panel.