Appliance Error Code Guide Codes, causes & fix order
Symptom

Washing Machine Will Not Fill

No water at all, or a trickle that takes twenty minutes: the fill path is short and almost every fault on it can be checked without a screwdriver. Work from the wall to the drum, not from the drum outwards.

Checked against manufacturer fill-time logic Updated 17 November 2026 9 min read

The short answer

  • Check the tap first — a half-open valve or a second tap behind the machine is the most common cause of all.
  • Then the inlet screens. Grit and scale collect in the mesh where the hose joins the machine.
  • Then the hose, for kinks and a crushed section behind the machine.
  • Then the valve, the level sensor and the door lock. Those are the parts that need the cabinet open.

The seven causes, in order

#CauseHow to checkTool needed
1Tap closed or partly openOpen fully; check whether the machine has two suppliesNone
2Household water off or low pressureRun a kitchen tap; ask whether the building is being worked onNone
3Blocked inlet screenTap off, hose off, look at the mesh in the machine inletPliers
4Kinked or crushed hosePull the machine out and follow the hoseNone
5Failed inlet valve solenoidListen for a click and check for 230 V at the valve when fillingMeter
6Pressure hose or sensorWater enters but the machine never registers itNone to inspect
7Door or lid lockMachine refuses to start the fill at all; lock does not clickNone to inspect

The inlet screens, properly

  1. Turn the tap off and unplug the machine.
  2. Unscrew the inlet hose at the machine end, not the tap end.
  3. Look into the inlet — a small plastic mesh sits inside. Pull it out with pliers and rinse it under a tap. Use an old toothbrush for scale.
  4. Look at the hose washer too. A perished washer can shed rubber into the screen.
  5. Refit and test with the hose straight. Flow should be strong within a few seconds.

On a machine with hot and cold inlets, check both. A washer that fills slowly on a warm programme but normally on cold is telling you the hot side is restricted.

When it is the inlet valve

The valve is a small block with one or two solenoids at the back of the machine. When the board calls for water it energises a coil, the valve opens and water passes. Two failures happen: the coil goes open circuit, or the valve body jams with scale and stays shut or stays open.

With a meter, check for supply voltage at the coil during a fill and for coil resistance across it. No voltage means the board is not commanding the valve — look at the wiring and the door lock. Voltage but no water means the valve or the screen.

Water in, but the machine does not know

If water is clearly entering and the machine still reports a fill fault, the problem is on the sensing side: the pressure hose, the air chamber or the sensor. That is the same fault family as the level codes — Samsung 1E / 1C, LG IE and Bosch E17 all point at parts of it.

Close the taps and unplug before disconnecting a hose. Inlet hoses are under mains pressure; a hose released with the tap open will spray across the room and can scald if the supply is hot.

Which part each check points to

FindingPartNotes
Water at the tap, none at the machineHose or screenClean the screen, replace a collapsed hose
Screen clean, no click from the valveValve solenoid or board outputTest voltage before replacing either
Valve hums but no waterValve bodyScale or a failed diaphragm; replace the valve
Fills constantly, never stopsValve stuck open or level sensorTurn the tap off now — this floods a floor
Water in the drum, no level readingPressure hose and sensorClean the hose and chamber first
No fill and no lock clickDoor or lid lockCheck the lock and its wiring

Repair or replace

An inlet screen clean is free, a hose is inexpensive and a valve is a modest part. If the machine has also been leaking, or the drum has started to rumble, the arithmetic changes — what a washer repair involves explains what a quote is paying for.

Frequently asked questions

Why did this start after the water came back on?

Sediment is disturbed when supply is restored. It travels to the nearest screen, which is usually the washer inlet. Clean the screens and the problem goes away.

The machine fills with hot water only — is that a fault?

If it is a dual-inlet machine, the cold side is blocked or its solenoid has failed. If it is a cold-fill-only machine, the supply is connected to the wrong tap.

Can I use the machine with a slow fill?

Short cycles may complete, but the machine is working to a timeout and will eventually stop mid-cycle. Fix the restriction rather than living with it.

Sources

  1. Manufacturer support guidance on fill-time faults and inlet filter cleaning (Samsung, LG, Bosch, Whirlpool and Electrolux support pages), accessed 17 November 2026.
  2. Service documentation on inlet valve circuits and pressure-sensing fill control.
  3. Editorial review against the parts trade: sediment and screen blockage after supply interruptions.

General information only. Inlet layout, valve type and code wording differ by brand and model. Confirm against your machine's documentation and unplug before opening any panel.