Appliance Error Code Guide Codes, causes & fix order
Dryers · LG

LG Dryer Error Codes: d75 to d95, and the Rest

LG's dryer codes are unusually honest: the number is the percentage of duct blockage the machine estimates. That makes the diagnosis easier than on any other brand — and it makes ignoring the code a genuine fire risk.

Checked against LG support documentation Updated 17 November 2026 9 min read

The short answer

  • d75 / d80 / d90 / d95 — the exhaust duct is estimated at 75, 80, 90 or 95 percent blocked. Same fault, different severity.
  • gAS (looks like 9A5) — a gas supply problem on a gas dryer.
  • Flow Sense bars — two or four bars mean the same restriction as the codes.
  • Clean the whole path: filter, duct behind the machine, the wall run and the outside hood. The dryer is only one third of it.

The codes in one table

CodeMeaningFirst check
d75 / d80Exhaust restriction estimated at 75–80%Lint filter and the duct behind the machine
d90 / d95Severe restriction, 90–95%Stop using it; clean the full duct run and the outside hood
Flow Sense barsThe same restriction shown graphicallyAs above
gAS / 9A5Gas supply problem (gas models)Gas valve open, other appliances working, then a licensed technician
dE / dCDoor not closed or detectedDoor catch, striker and the switch
tETemperature sensor faultSensor and harness
HEHeater faultHeater circuit and thermal fuse

Code wording differs slightly across model generations and countries, but the airflow logic is the same on every LG dryer: the machine compares the temperature rise and the moisture it is removing against what it expects, and estimates how restricted the exhaust is.

The airflow path, end to end

  1. Lint filter — clean it after every load. A filter with a film of fabric softener should be washed in warm water and dried.
  2. The duct inside the dryer — lint builds up around the blower housing. This is a service job on most models.
  3. The flexible duct behind the machine — it must not be crushed, kinked, or coiled like a spring. An S-curve of one or two gentle bends is fine; a concertina or a compression is not.
  4. The wall run — long runs with several elbows collect lint at every bend. Rigid duct is better than flexible.
  5. The outside hood — flappers that do not open fully, or a bird's nest, will produce exactly these codes.

A simple test: run the dryer on air only and stand outside at the vent. Strong, warm airflow means the machine is fine and the code is about the load. Weak or no flow means the restriction is real and downstream.

A restricted dryer vent is a fire risk, not just an efficiency issue. Lint is highly flammable and the heater runs hotter when airflow falls. Clean the duct before using the machine again, and never run a dryer with the vent disconnected into a room.

The gas code

On a gas dryer, d80 can also mean insufficient gas. The display shows the word GAS, which on a seven-segment display reads like "9A5". Check the shut-off valve behind the dryer is fully open and that the hob lights normally. If gas is present and the code stays, the burner or its valve needs a technician — do not open gas fittings yourself.

When it is not airflow

SymptomLikely faultNotes
Tumbles, no heat, no codeThermal fuse, heater element, thermostatCheck the fuse first — it usually fails for a reason
Heat, but clothes still damp after two cyclesAirflow, or a moisture sensor that needs cleaningClean the sensor bars inside the drum
Stops immediatelyDoor switchCheck the catch and the switch
Loud rattle with heatDrum roller or beltMechanical, stop using it

Repair or replace

Most d-codes cost nothing but a ladder and an hour. If the machine has been running restricted for a long time, the thermostat and heater may also have been damaged, which changes the arithmetic — see repair or replace.

Frequently asked questions

The code cleared after cleaning, but came back a week later — why?

The wall run or the outside hood is still partly blocked. The lint you removed was the part you could reach.

Does a shorter duct always solve it?

It helps, but the biggest factor is bends and crushed sections. A short flexible duct squashed behind the machine is worse than a longer rigid run with gentle turns.

Can I reset the code without cleaning?

You can clear the display, and the machine will run again. The restriction remains, and the next code will be d90 or a failed thermostat.

Sources

  1. LG support — dryer error code lists and the d90/d95 duct blockage guidance (US support pages), accessed 17 November 2026.
  2. LG documentation on the Flow Sense restriction indicator and the gas supply display code.
  3. Editorial review against the parts trade: lint accumulation patterns and thermostat failures after long restricted running.

General information only. Code wording, duct specification and gas connections differ by model and market. Gas work belongs to a licensed technician.